Showing posts with label YAESU. Show all posts
Showing posts with label YAESU. Show all posts

11 December 2012

A proposed root cause for the "Withering Filters" phenomenon

Fig. 1 Photo by Jerzy,
SP6FPY. 
(Click to enlarge)
After having examined the failure mechanism of more than 100 ceramic filters that have succumbed to electromigration, I think I have collected enough data to propose a root cause for the phenomenon that has caused failure of a very large numbers of filters. I should gratefully thank the many fellow radio amateurs that have sent photos of their filters to me, adding to my database on the subject. Manufacturers might want to consider changing their production methods to avoid the chain of events that I propose that leads to this phenomenon.

So, let's look at the data I have collected and a proposed theory that explains the facts:

Fig. 2. Note the water droplets.
1) In all of the ceramic filters I have examined, there was a surprising quantity of water inside the plastic case (take a look at Figs 1, 2 and observe the signs of water presence on the elements and inside the black case, also the whitish flux residue on the case of the adjacent filter in Fig. 1, which shows that a quantity of water evaporated from that surface, leaving it behind). The water inside the case causes the filter to fail soon after the transceiver circuit applies DC voltage to the input, and mainly the output pins of the filter. The quantity of water is such, that can't be attributed to a filter manufacturing flaw: it's just too much. I can't imagine that the filter manufacturers would have ignored it. Also, I haven't found water inside some new filters I have "dissected". So, there must be another reason for this quantity of water inside the filter.

2) Where does the water come from, if not from a filter manufacturing flaw? I think the answer lies with the newer technologies and materials used for the fabrication of populated printed circuit boards (PCBs). Briefly, the new methods of wave soldering with non-Pb solders extensively use organic acid (OA) fluxes. Those fluxes are removed from the PCBs after wave soldering by pressure rinsing with hot water. The rinsing process takes some time to complete.

3) I think that the water ingress can be explained thus. The rinsing process uses hot water (about 70 degrees Celsius), sometimes with ionic additives. This (as well as the previous soldering process) causes the (so far dry) air inside the plastic filter case to expand, creating positive pressure inside the filter case. This results in air escaping from inside the filter case, as the temperature softens the plastic case and compromises the (not so great to begin with) sealing at the bottom of the filter case.
When the PCB exits the rinsing process, water is held by affinity under the filter case, between the filter and the PCB surface. The filter starts cooling down, and this causes the pressure inside the filter to drop under the atmospheric pressure. This negative relative pressure tends to draw a small quantity of the water under the filter inside the filter case, through the very fine cracks at the filter case seals that the positive air pressure (when the filter was hot) created. The quantity of the water is some micrograms, but it's more than enough to cause trouble. The board is then dried, but the accident has already happened. The water is already inside the filter.

4) Once inside the filter, the water can't escape and remains trapped inside the case. Some of it condenses or moves on the filter plates, starting the electromigration process where the electric field (due to the externally applied voltage) reaches sufficient value. This most often occurs at the corners of the thin output ceramic plate (element) at the output of the filter, which is only about 0.35 mm thick. This leads to the failure of the filter after some time.

5) What might be a solution? A slight modification of the rinsing - drying process might help in avoiding this phenomenon.
If the PCB is dried IMMEDIATELY after exiting the rinsing chamber with pressurised HOT air, then the water might not get inside the filter case, as the pressure difference doesn't occur this way before the water has been removed from under the filter.
I have no further knowledge of the exact conditions used in any particular case, so the above proposal may not always apply. But each manufacturer could certainly review the method used and modify it accordingly, so as to avoid the conditions that drive water inside the filter case (and possibly inside other "sealed" components, such as miniature relays).

If someone with more knowledge of the PCB processing methods wishes to add (or correct!) something in the above, please send an e-mail to sv8ym@raag.org.

73 DE SV8YM

Addendum: The above suggest that if you repair (clean and dry thoroughly with hot air) or replace a filter that has gone bad through water ingress during the rinsing procedure with a brand new one that hasn't come in contact with water, you may not have problems in the long run, even if you don't also install DC-blocking capacitors. That is so because you need BOTH water AND a voltage gradient to start electromigration. A completely dry filter probably can withstand 7-8 V indefinitely (as experience with older rigs shows - the PCBs were washed with organic solvents a long time ago, in the paleolithic Pb era!).
 

07 April 2012

The ailing ALC of the venerable FT-ONE - a gooey story

I recently got to restore an FT-ONE to full working order.   This particular FT-ONE brought back memories from 25 years ago, as it used to belong to a good friend in whose shack I drooled all over it, as it was the "Yaesu flagship" of the mid-eighties. That friend sadly passed away a few years ago, and the rig, after staying idle in storage for some years, was bought by another friend who sent it to me to shape it up, as it was quite unusable.
After fixing several problems (among them xtal oscillators that didn't want to go where they were supposed to and also an obnoxious general case of acute screwdriveritis the rig had gone through) and proceeding to full alignment, I stumbled across a most peculiar problem: The ALC was acting up. Although I could balance the directional coupler on 28 MHz (as indicated in the service manual), and then I could complete the ALC alignment transmitting into a dummy load, after a few hours, when first switched on and put to TX, the rig had a very low RF output (10 - 20W) and showed a large SWR indication for no apparent reason (transmitting into a dummy load). If I went on transmitting a carrier for a minute or so, the power would slowly come up, but even then it never reached more than 60 W or so on 1.85 MHz, and various other levels on the other bands - also, the ALC indication was fluctuating for no apparent reason.
Fig. 1 The gooey stuff!
I thoroughly checked the ALC board, suspecting a bad germanium diode - all checked out OK, as did all the transistors and trimpots on that board. Nothing there. I started suspecting some other part of the ALC feedback loop, but then my brain - in a rather rare epiphany - took in what my eyes had been seeing all along. Take a look at Fig. 1, click to enlarge.
Do you see the (kindly provided) red arrow? It points to a blob of some kind of gooey glue material intended to keep the directional coupler  toroid in place. I grabbed my ohm meter probes and placed them on two spots on the goo blob. Bingo! The goo was conductive! I read an indication of about 100 Kohm with the probes spaced a few millimeters. So the conductive goo was "leaking" RF current into the reflected power detector (D01), fooling the ALC circuit into believing that a serious SWR existed, so it promptly proceeded to reduce the output power (Yaesu calls this the APF function). Observe in the picture that the goo covers both the TX line (the bare thick wire through the toroid) and the winding ends on the right (where the enamel insulation had been removed).


Fig. 2 Off with the goo!
How to fix? Simple! Take a look at Fig. 2 (the "after" picture!). Using a thick needle, I scraped off as much of the brown goo as I could. I almost took it all off, it's hardened and breaks off in little chunks. I was careful not to scrape off the enamel insulation from the toroid windings.
After removing the goo, everything returned to normal. The ALC alignment went extra smoothly, and the power output is steady and OK on all bands. The high SWR protection now works perfectly.
This nasty goo has crossed my path for the second time: An old TS-440 that would impulsively unlock its PLL had plenty of the same goo on the VCO components. The resulting inter-component leakage was causing the PLL to unlock. It seems that with age this stuff oxidises and becomes conductive, upsetting sensitive circuits like VCOs and directional couplers. I wonder what brand name that goo was!!

20 October 2010

Does your FT-857 display look like a zebra?

I have come across several cases of malfunctioning display in the control head of the FT-857, where several "scan lines" in the dot-matrix display cease to function, so the display seems "streaked" at places. In extreme cases, the display becomes difficult to read. The funny thing is, the streaks come and go, or seem to move about the display with time! I finally got to open a control head belonging to a friend to see if there was something that could be done. The photo (click to enlarge) shows the display module ribbon, which is soldered directly to the PCB. The connections on the PCB turned out to be OK, so I checked the LCD side. I couldn't spot anything there either, but I saw that flexing the flexible ribbon near the LCD glass made some of the streaks come and go. The flexible ribbon is attached to the LCD glass with epoxy material. This reminded me of my experience with my Sony F-717 camera, where the epoxy material holding the CCD sensor on its carrier had softened due to heat and humidity, making the connections fail - the CCD had to be replaced. Perhaps the control head of the '857, when subjected for a long time to the temperature extremes and humidity inside a car, suffers a similar degradation of the epoxy material at the LCD display, eventually causing those streaks to appear. All of the affected units I know of were actually being used in cars! For the time being, I can't think of a solution, except of course replacing the whole display module - a bit tough.
So, my advice is, don't leave the control head(s) in your car exposed to the sun, humidity and temperature extremes, the dot-matrix display might become "streaky"! I, for one, have always covered the FT-857 control head in my car with a piece of black cloth, protecting it from strange eyes and the deleterious effects of sunlight. After five years in the car, it still operates fine.

I'll keep my fingers crossed - and my control head covered!